There are really only two books that have inspired me to model specific subjects. The one that matters to this discussion is Pierre Clostermann’s diary “The Big Show.” In it is an unvarnished account of the author’s time as a Free French pilot in the RAF in command of both the legendary Spitfire and the brooding Tempest Mk V. To me the Tempest with its gaping maw, cuts a profile of a bare knuckle boxer, a hard-as-coffin-nails street fighter. The Tempest exudes a singular purpose of power in a way the more elegant Spitfires, Mustangs and Lightings do not. And, having recently made the transition from 1/48 to 1/32 I had to build not only a Tempest, but one of Clostermann’s.
Enter the Special Hobby 1/32 high tech Tempest Mk. V. I read several in box reviews and was amazed at the level of detail that Special Hobby had appeared to achieve. I ordered one and dove in with excitement and high expectations. I must admit that my initial expectations of the kit were too high, and that is not the fault of Special Hobby but of Tamiya. I had just completed Tamiya’s 1/32 Corsair and that unfairly set a bar that few kits could achieve. But, Special Hobby is not let off of the hook. While the detail is truly tantalizing, especially the cockpit, the fit and assembly is often immensely frustrating.
With a few tweaks, Special Hobby could have an exceptional kit on their hands. What Special Hobby currently has is inarguably one of the two best Tempest Mk V in 1/32 scale (note: there are only two Tempest V kits available in 1/32 scale). Make no mistake, if you are willing to invest the work, Special Hobby’s Tempest will build into an impressive and substantial display piece, but it will provide many hours of frustration and unnecessary work to get there.
I will not recount every step of my build that spanned over ten weeks, or each of the many areas that I believe needed improvement. Some of those issues could be problems I created. I will, however, address a few areas that provided me the most trouble.
- Wheel Bays: This is the place that needs a redesign from Special Hobby. The instructions provided in my kit were incorrect (they were correct in my version of their Mk II). The construction is unnecessarily complicated and finicky. Slight misalignments in this stage can throw off the alignment of the top wing, thus throwing off everything from the fit of wing tip lights, to the inserts Special Hobby created for the inner wing to allow the same wing moldings for the Mk. V and Mk. II. Later in the construction, Special Hobby wants the builder to install about a dozen small parts, all of which required varying degrees of modification to fit correctly. Most troubling were the fit of the knuckle where the main landing gear struts connect to the wheel bays. I had to modify them until they were almost unrecognizable. It all worked in the end, but I think that was more my will than the kit. Special Hobby should look at creating a one piece resin wheel bay insert. This would fix the correct proportions and alignment of all of the important parts.
- Cowling: The focal point of the Tempest V is the prominent yawning radiator/oil cooler inlet. Special Hobby created a sub assembly with the radiator faces sandwiched between two halves of the engine and radiator cowlings. After dry fitting and trying to correct the fit of this multiple part affair,
I decided the best way to assemble these parts is to ignore the steps suggested in the instructions. I glued the cowling halves together so as to be able to fill and sand the prominent seams on the inner and outer surfaces of the radiator scoop. Then, I had to sand down the radiator faces to fit into the assembled cowling. The next step is to fit the assembled cowling onto the assembled fuselage. Every build I’ve seen of this kit has had some sort of significant step/gap between the engine cowling sub assembly and the fuselage, so I am not alone. The fit of the cowling halves required substantial sanding and filling that required a great deal of riveting and scribing to resurrect from plastic sanded smooth.
Ultimately the rule on this kit is simple: dry fit constantly, plan ahead, and give yourself plenty of time to build it. This kit can’t be rushed. The Tempest requires the builder’s full attention (ironically, I think this was said by her pilots, too). With time, patience and intermediate skill, a great result awaits. As a good friend who has built the kit said, “this is the best-worst kit you’ll ever build.” In sum, it’s modern Tamiya level detail with 1960’s era Revellogram fit.
Here is an album of un-narrated pictures during the build process.[ngg src=”galleries” ids=”45″ display=”basic_thumbnail” thumbnail_crop=”0″]